AL Priority Firmware Update History (Running History)

[Clint Eastwood]

I updated everything a few hours ago... one puzzle. I have it setup silent startup. When it finally goes into defense mode (much longer than before... seems like maybe a minute) it makes a little drum beat sort of sound... but as I drove it did the little drum noise again another minute after that.. not sure what that was about.

[tawwwd]

Did you enable skip first warm up? That would probably be your minute delay

[Clint Eastwood]

Did you enable skip first warm up? That would probably be your minute delay

Well there appears to be 2 - 1 minute delays. I did not change anything other than use defaults, silent startup. After 1 minute, the light goes purple and does that drum beat... then another minute - another drum beat. I was already driving down the road when I heard the second one and thought... what is that?

I have it recorded on dash cam audio.

[Clint Eastwood]

For the record, that double-init issue I had the other day has not occurred again. Must of been some glitch.

[CommandrKeen]

A couple comments on the new update.

After updating, when I press both buttons on the hifi control set, I no longer go into menu mode. Nothing happens. I've tried short presses of both buttons and long presses of both buttons. Even tried short and long presses of each button individually. I can't seem to get into the menu options any more. Anyone else experience this, or perhaps I am doing something wrong?

Second comment is do most people perform the self test at startup? I have always turned it off, but wonder now if that is a best practice.

[BestRadarDetectors]

A couple comments on the new update.

After updating, when I press both buttons on the hifi control set, I no longer go into menu mode. Nothing happens. I've tried short presses of both buttons and long presses of both buttons. Even tried short and long presses of each button individually. I can't seem to get into the menu options any more. Anyone else experience this, or perhaps I am doing something wrong?

Second comment is do most people perform the self test at startup? I have always turned it off, but wonder now if that is a best practice.

Both Buttons is only to adjust the volume. To go into the menu you just need to press and hold the menu button.

[CommandrKeen]

Sorry, I should have stated that I was trying to adjust the volume. When I put the setup file on the USB, I set the volume to 5. This is way too loud, so I wanted to adjust down to 4 or possibly 3. I can't do this with the control set. My bad, I thought both buttons also got you into the menu. I'm still new to the Hi-Fi as I previously only used the BT module.

Even still, holding the menu button won't put me into the menu. The light flashes on the hi-fi control set, but the buttons don't seem to do anything.

[BestRadarDetectors]

Sorry, I should have stated that I was trying to adjust the volume. When I put the setup file on the USB, I set the volume to 5. This is way too loud, so I wanted to adjust down to 4 or possibly 3. I can't do this with the control set. My bad, I thought both buttons also got you into the menu. I'm still new to the Hi-Fi as I previously only used the BT module.

Even still, holding the menu button won't put me into the menu. The light flashes on the hi-fi control set, but the buttons don't seem to do anything.

Hold both buttons and when the light turns purple release both and then either press the Menu (Up) or Power (Down) and it should say Volume 2, 3, Etc.

[CommandrKeen]

I gave it a try over lunch to confirm and pressing the buttons no longer works on the hi-fi control set following the update. Can I rollback the change and apply again? I reinserted my USB that I updated with a couple days ago and all it did was reload the setup file (I Have a parking mode only setup that I can plug in when needed), but did not reapply the firmware. Any help is appreciated.

[BestRadarDetectors]

I gave it a try over lunch to confirm and pressing the buttons no longer works on the hi-fi control set following the update. Can I rollback the change and apply again? I reinserted my USB that I updated with a couple days ago and all it did was reload the setup file (I Have a parking mode only setup that I can plug in when needed), but did not reapply the firmware. Any help is appreciated.

Did you ever update the firmware on the HiFi Controller since you purchased it? Not talking about the CPU Firmware.