AL Priority - What Have I Been Hit By?

[tawwwd]

You might have had one long alert but if they released the trigger and pulled it again the second pull would register as another hit but it might have been the same encounter so you did not realize it.

Could be the case. All 3 alerts seemed to go the full 4 sec JTK then blinked green.

I got one of the overpass hits on camera.

http://vid1052.photobucket.com/album...psbuiz9vfh.mp4

[oddpedestrian]

Could be the case. All 3 alerts seemed to go the full 4 sec JTK then blinked green.

I got one of the overpass hits on camera.

http://vid1052.photobucket.com/album...psbuiz9vfh.mp4

I can't see this could you upload to YouTube?

[tawwwd]

I can't see this could you upload to YouTube?

Sure

[hussein]

Sure

lol, OT, but when I saw the Youtube preview image, I was like hmm that looks like AB!

[tawwwd]

lol, OT, but when I saw the Youtube preview image, I was like hmm that looks like AB!

Haha!
How could you tell?!

I think this place is the speed enforcement capital of the universe! I believe these vans are the dragoncam laser ally? I really wish there was a way to confirm a jam from our end!

[Qui-Gon]

Haha!
How could you tell?!

I think this place is the speed enforcement capital of the universe! I believe these vans are the dragoncam laser ally? I really wish there was a way to confirm a jam from our end!

Your confirmation is the BEEEEEEEEEEEEEEP you hear!

[hussein]

Haha!
How could you tell?!

I think this place is the speed enforcement capital of the universe! I believe these vans are the dragoncam laser ally? I really wish there was a way to confirm a jam from our end!

If your sensors are the same height, depth, level with the ground, 18" apart, you should be good. No tickets is a good delayed indicator, heh.

[JStump2490]

lol, OT, but when I saw the Youtube preview image, I was like hmm that looks like AB!

Looks like I might be upgrading to rear heads soon after seeing this

[tawwwd]

If your sensors are the same height, depth, level with the ground, 18" apart, you should be good. No tickets is a good delayed indicator, heh.

theyre perfectly straight and I have coverage of my plate and all the chrome on my bumpers.

They do point up just a little because of the rake on my truck (back end site 3/4" higher than the front). I was going to adjust it and make it flat but I figured that might be better because of the angle on the overpass shots. Seems to work so far.

[modsl55amg]

Your AL Priority is still a virgin... Here are my stats:

Device information
Serial number XXXXXXX
Firmware version 4.2.2
Region North America
Power Cycles 96
Control Set FW version 2.4
Control Set HW version 1
Settings
Audio Volume 3
Parking detection range 3
Silent Power-up Disabled
Dark Mode Disabled
Parking enabled sensors Front1, Front2, Front3, Rear1, Rear2
GPS Antenna Enabled
PDC Speed Limit n/a
Working mode Parking and Laser Interference Defense
Pro mode Disabled
LID Speed Limit n/a
Radar Antenna Model STIR+
Radar Settings X, K, Ka
LID Time Unlimited – Test purposes
Specific LID settings
Vitronic Poliscan
Speed scanner Enabled
Unicam Camera
Section speed control All sensors ON
NJL SCS
Speed-laser Enabled
Riegl
Speed-laser Enabled
Trafic Observer
Speed scanner Enabled
Stalker
Speed-laser Maximum Power
Alerts by Source Speed-laser
Marksman and UltraLyte 50
Atlanta SpeedLaser Stealth 2
Kustom ProLaser 1 2
Kustom ProLaser & ProLite 39
Redspeed SpeedGuard 0
Riegl 0
Stalker 156
LTI Truspeed 76
Unipar - SL700 0
NJL SCS 101 & 102 0
Jenoptik – Laveg 0
Leivtec XV 2 0
Laser Ally 240
Error Sensitive Lasers
Jenoptik LaserPatrol 0
Jenoptik TraffiPatrol XR 0
ProLaser 2 & Atlanta SpeedLaser 8
Speed Section Control
Camea - IR Camera 0
Speed Scanner
Traffic Observer 0
Vitronic Poliscan 9
Radar
K-band 0
Ka-band 0
X-band 0
POP 0

Tom (BRD),

Regarding the "Print Settings & Use Statistics" feature of the ALP system:

1. Is the firmware upgrade for this feature supposed to be installed into the ALP system when the other files are installed via a Flash Drive, e.g. (Uxxxxxxx.bin, UCSTHIFI.BIN, VOICEPAKCK.ALP, setup.alp), in order for the system to collect/store data for later retrieval?

2. Or is the "Print Settings & Use Statistics" firmware supposed to be loaded onto a Flash Drive, then inserted into the flash drive port EACH time the owner wants to retrieve information from the system that the "Settings & Use Statistics" feature provides, and writes onto the flash drive while it is inserted?

Thank you in advance for your advice.