LED constant blue and two beeps = cable or defective sensor. please help

Printable View

06-12-2016, 08:23 PM
rxbg

LED constant blue and two beeps = cable or defective sensor. please help

Hello all,

system and car are 2 months old. began having this error code come up on start up. also have the ALP connect/BT. no integrated speaker. ran a config log and posted below. could it just be that there is a slight power issue upon start up? (my other car with a different anti laser does the same thing but it is a well known problem and i know all sensors are working because when i turn the power to the system on and off again the error goes way) however, when i cycle it on and off in this car the error doesn't go away. really hoping i don't have to take it into the installer because he's an hour away and the install was a B in this SUV. i would doubt the sensor itself is defective since it is a new system. hope the info below helps at all? also- the BT connection goes out sometimes while i am driving but quickly reconnects on its own. also- it always mutes when i am on a call and i thought that in HFP mode it would not do that.

Serial number 4576019
CPU Hardware version 2
Firmware version 5.2.3
Region North America
Power Cycles 535
Control Set FW version 3.6
Control Set HW version 1
Activated locks not active
Hardware version 2
Connected sensors
Connected sensors (memorized) Front1, Front2, Rear1, Rear2
Connected sensors (actual) Front1, Front2, Rear1, Rear2
Connected TX sensors (stored)
Connected TX sensors (actual)
Profile A
Settings
Audio Volume 5
Parking detection range 9
Silent Power-up Disabled
Dark Mode Normal
Parking enabled sensors
GPS Antenna None
PDC Speed Limit NONE
Working mode Parking and Laser Interference Defense
Pro mode Disabled
LID Speed Limit NONE
Below set LID Speed Limit PDC & DLI
Radar Antenna Model STiR
Radar Settings K, Ka
LID Time Unlimited – Test purposes
After LID timeout DLI & Warm up
Audio volume of Laser Alerts 6
Audio volume of Radar Alerts 6
Menu button short press function None
Specific LID settings
Vitronic Poliscan
Speed scanner Enabled
Unicam Camera
Section speed control Front sensors ON
NJL SCS
Speed-laser Enabled
Riegl
Speed-laser Enabled
Trafic Observer
Speed scanner Enabled
Stalker
Speed-laser Maximum Power
ARH TrafficSpot
Speed scanner Disabled
Profile B
Settings
Audio Volume 3
Parking detection range 3
Silent Power-up Disabled
Dark Mode Normal
Parking enabled sensors Front1, Front2, Front3, Rear1, Rear2
GPS Antenna None
PDC Speed Limit NONE
Working mode Parking Detection only
Pro mode Disabled
LID Speed Limit NONE
Below set LID Speed Limit PDC & DLI
Radar Antenna Model Not Connected
Radar Settings
LID Time 3 seconds
After LID timeout Warm up
Audio volume of Laser Alerts 6
Audio volume of Radar Alerts 6
Menu button short press function None
Specific LID settings
Vitronic Poliscan
Speed scanner Enabled
Unicam Camera
Section speed control Front sensors ON
NJL SCS
Speed-laser Enabled
Riegl
Speed-laser Enabled
Trafic Observer
Speed scanner Enabled
Stalker
Speed-laser Maximum Power
ARH TrafficSpot
Speed scanner Disabled
Profile C
Settings
Audio Volume 3
Parking detection range 3
Silent Power-up Disabled
Dark Mode Normal
Parking enabled sensors Front1, Front2, Front3, Rear1, Rear2
GPS Antenna None
PDC Speed Limit NONE
Working mode Parking Detection only
Pro mode Disabled
LID Speed Limit NONE
Below set LID Speed Limit PDC & DLI
Radar Antenna Model Not Connected
Radar Settings
LID Time 3 seconds
After LID timeout Warm up
Audio volume of Laser Alerts 6
Audio volume of Radar Alerts 6
Menu button short press function None
Specific LID settings
Vitronic Poliscan
Speed scanner Enabled
Unicam Camera
Section speed control Front sensors ON
NJL SCS
Speed-laser Enabled
Riegl
Speed-laser Enabled
Trafic Observer
Speed scanner Enabled
Stalker
Speed-laser Maximum Power
ARH TrafficSpot
Speed scanner Disabled
Alerts by Source Speed-laser
Marksman and UltraLyte 0
Atlanta SpeedLaser Stealth 0
Kustom ProLaser 1 0
Kustom ProLaser & ProLite 1
Redspeed SpeedGuard 0
Riegl 0
Stalker 0
LTI Truspeed 0
Unipar - SL700 0
NJL SCS 101 & 102 0
Jenoptik – Laveg 0
Leivtec XV 2 0
Leivtec XV 3 0
Laser Ally 0
Cam S1 0
ARH TrafficSpot 0
Error Sensitive Lasers
Jenoptik LaserPatrol 0
Jenoptik TraffiPatrol XR 0
ProLaser 2 & Atlanta SpeedLaser 0
Stalker XLRr 0
Speed Section Control
Camea - IR Camera 0
Speed Scanner
Traffic Observer 0
Vitronic Poliscan 0
Radar
K-band 449
Ka-band 29
X-band 5
POP 3
MultaRadar CD 0
06-12-2016, 08:42 PM
BestRadarDetectors

Post a video of the startup routine so I can see and hear what you are mentioning.
06-13-2016, 12:45 AM
Holla

wow 9 starts a day lol 535 power cycles impressive for 2 months
06-13-2016, 11:36 AM
rxbg

https://www.youtube.com/watch?v=hO1v...r#action=share

https://www.youtube.com/watch?v=hO1v...r#action=share

ALSO- the car has auto start stop so maybe that is why so many on/off cycles?
06-13-2016, 12:46 PM
BestRadarDetectors

Those are not error codes. If there was an error the LED would be Red and it would also give a long alert tone which would repeat to correspond with the error code. For example if the system was triggering an Error 2 you would hear two long beeps and the LED would be Red.
06-13-2016, 01:06 PM
rxbg

shouldnt the light be green at the end? why is it blue?
06-13-2016, 01:17 PM
Holla

blue means you are in defense mode--ready to jam
06-13-2016, 01:25 PM
rxbg

great. can you plewase address how to make sure i can hear warnings with BT connection when i am on the phone?
06-13-2016, 01:48 PM
BestRadarDetectors

Quote:

Originally Posted by rxbg

great. can you plewase address how to make sure i can hear warnings with BT connection when i am on the phone?

If using BT you would get a verbal notification and it would also be on the screen and get recorded in the log history.
06-13-2016, 02:13 PM
radargeek

Those are the normal startup beeps. You can select "silent power-up" in the settings if you don't want to hear them.

Here's an interesting piece of trivia I read somewhere: the startup beeps are the letters "AL" (for AntiLaser) in Morse code. :)
06-13-2016, 02:29 PM
rxbg

great,. thank you all for you help. thanks bestradardetectors!
06-13-2016, 05:04 PM
RedRocket

Quote:

Originally Posted by radargeek

Here's an interesting piece of trivia I read somewhere: the startup beeps are the letters "AL" (for AntiLaser) in Morse code. :)

@rxbg
1. A = dit dah ( . _ )
2. L = dit dah dit dit (. _ . . )

A few members here are Amateur Radio Operators (Ham's) who know the Morse Code, myself included.
06-13-2016, 11:10 PM
modsl55amg

Quote:

Originally Posted by RedRocket

@rxbg
1. A = dit dah ( . _ )
2. L = dit dah dit dit (. _ . . )

A few members here are Amateur Radio Operators (Ham's) who know the Morse Code, myself included.

Son of a gun! Until radargeek mentioned that the startup beeps may stand for AL, and you wrote the Morse Code for AL, I thought the beeps were just that...random beeps. But, after I listened to rxbg's startup video, well, son of a gun! It is the Morse Code for AL! I had to learn Morse Code in the Navy, back in 1969. I have had my ALP systems configured for Silent Power-up since shortly after they were installed, so I only heard the startup beeps a couple of times, and never recognized that the beeps were Morse Code.
06-14-2016, 07:15 AM
RedRocket

Quote:

Originally Posted by rxbg

shouldnt the light be green at the end? why is it blue?

@rxbg
hmmm, to the above quote. I'm curious, do you know the meaning of these 2 terms & how they should be practised ?
1. JTK
2. JTG
09-16-2016, 07:20 PM
rxbg

jam to gun is the latter i dont know the former
09-17-2016, 08:49 AM
RedRocket

Quote:

Originally Posted by rxbg

jam to gun is the latter i dont know the former

@rxbg
Here ya' go -

http://www.radarandlaserforum.com/sh...rs-such-as-JTG