Tried two different USB's here.
Printable View
Tried two different USB's here.
What fails? The save of the file? Did you register this unit?Quote:
Originally Posted by 64pvolvo1800
Yes. This is the last one I got and put on the S60 Volvo. It has saved me a few times already and with the bT or control set it boots fine and goes blue. Settings still show 4.3.5 but USB save fails. I'm using a different drive than before and it's fat32. I will try another USB.
Sent from my iPhone using Tapatalk
Can I use a USB with an SD or CF card as long as it's fat32?
Sent from my iPhone using Tapatalk
Only real USB drives are supported. You cant use an SD Card in a USB adapter.Quote:
Originally Posted by 64pvolvo1800
Yes, mine is registered I have received confirmation Email.
I have to get my kids ready for school. Will work with anyone having issues when I return.
Sent from my SCH-I605 using Tapatalk
Trying a different file w all new setup, ucset, and sn fw file. Took off properly. Did I have to have a new setup file to launch the update?
Sent from my iPhone using Tapatalk
No but its fine if you load another one.Quote:
Originally Posted by 64pvolvo1800
Sent from my SCH-I605 using Tapatalk
Well I'm good here. On to the other alp when I get home! Thanks as usual Tom. Good support and product in one stop shopping.... Muchos muchos grassy ass
Sent from my iPhone using Tapatalk
I deleted the file and downloaded a new one, it seems to be working fine now.
Try again and let me know what happens.Quote:
Originally Posted by dragons
Sent from my SCH-I605 using Tapatalk
As I said in my last post.. All good now.
Looks like we responded at the same time and I did not see your reply. If anyone else has an issue let me know.Quote:
Originally Posted by dragons
Completed update before work, checked stats...4.3.6 is uploaded to my CPU. Thank you Tom!!!
A total of how many new files are we loading?
Sent from my Z30 using Tapatalk
Firmware + Control Set + Current Setup File if you use the Control Module, If you are using ALP Connect you do not need the Control Set firmware.Quote:
Originally Posted by wolfpacal
Can somebody please post a step-by-step process of updating? What might seem simple to you may not be as simple to somebody else like me :(
Sent from my iPhone using Tapatalk
This should hopefully answer your question:Quote:
Originally Posted by TOMMYJR9
http://radarandlaserforum.com/showth...wfull=1#post30
Tom, please correct me if I am wrong.
Yes.. Process is the same as above.
Sent from my SCH-I605 using Tapatalk
Mission done , 4.3.6 and 3.2 , checked by the stats .
Résumé of the steps :
Go to : http://www.alpupdate.com/
1)go to '' Firmware upgrade'' , write your serial number @ Control Box update
press enter , do your math , press download , save to pc , file is = u\serial\.bin , go to next step
2) go to ''Control Set update'' , download to pc , save resulting file to pc = UCSET.bin
Take those 2 files and copy them on your usb key.
Go to your system , start it , place the key and wait , it will cycle for less than a minute ,
when all is done it will come back to flashing blue .
I did close and open again the system , tough the 2 files were already installed .
Please correct me if i skip something , when you have done this a few times ,
the routine is very fast .
When the stat file is pulled you should read 4.3.6 and 3.2 on your sreen.
==============================================
Off Topic
Tom if someone want to revert to a previous version , for a reason or another ,
can it be done ?
By default no you can not downgrade. Can it be done if really needed with distributor assistance yes but there should never be a reason to go backwards. All Software released is already Beta tested by the distributors for 1-2 weeks before public release to make sure there are no issues.Quote:
Originally Posted by Tman
So I presume for those of us who switch between the BT module and control set, the control set has to be connected to update UCSET.bin? Rather, does the control set firmware actually live on the little controller, or does it live on the ALP control box itself?
Yes, The control set would need to be connected to also update the Control Set. The firmware is installed directly onto the Controller.Quote:
Originally Posted by jdong
Just got my notice..and a ? I know has been asked plenty but if I have both files UXXXXXXX.bin and UCSET on the thumbdrive and restart twice will it update both or must I remove UXXXXXX.bin and do UCSET on it's own ?
The firmware file will get deleted automatically after the install and you will only be left with the Control Set firmware & Setup File if you are loading all three. After reboot just turn off and back on and within a few seconds you are done.Quote:
Originally Posted by Nanook
Got mine updated. Bring on the DALA!
P.S. The software you run on this site really pisses me off! I use a vpn for the sole purpose of staying off the grid but this site (the only one I have ever encountered that blocks the vpn btw) will not let me on the site. Apparently it blocks everybody on the choopa network. I seriously doubt it would stop somebody from hacking or implementing a botnet against the site if they know what they are doing.
You have no idea how many attacks we block daily from these networks. Last check we blocked almost 300,000 fake registration attempts alone and that is not to mention all the other types of attacks we get. If the network is blocked its because we were attacked through it.Quote:
Originally Posted by ProStreetCamaro
Enough to take some tylenols , did'nt think so many jaleous\bad people in this little world of cms.
Both vehicles updated today successfully! Thanks ALP and Tom/Mirage.
Quote:
Originally Posted by BestRadarDetectors
Good lord that is allot of fake registrations! If I switch from east coast server to Florida server it let's me on lol.
Firmware version 4.3.6
Region Australia & Pacific
Power Cycles 327
Control Set FW version 1.3
Control Set HW version 4
is the above correct
no showing the control set 3.2
Updated no problem, thanks all
no gps working spent hour messing around, does any one test the oz f/w etc before release also cant up grade controller been on test, k band not working properly, gps is enabled in set up
Firmware version 4.3.6
Region Australia & Pacific
Power Cycles 327
Control Set FW version 1.3
Control Set HW version 4
is the above correct
no showing the control set 3.2
Your Control Set FW is very outdated.. Should be 3.0 or 3.2Quote:
Originally Posted by dinkydi
I have also never seen anyone with a Control Set HW version 4, I have been on version 1 since Day one and it has never changed. Are you sure that is correct?
yes, and i have all ways up dated every thing before, they were a copy and paste from my stats i pulled
just done stats againQuote:
Originally Posted by BestRadarDetectors
Firmware version 4.3.6
Region Australia & Pacific
Power Cycles 374
Control Set FW version 1.4
Control Set HW version 4
I'm pretty sure those are the numbers shown for the ALP Connect module. My ALP Connect shows the same version numbers (1.4 and hw version 4)Quote:
Originally Posted by BestRadarDetectors
disconnected every thing direct to controller no bt no rg, tried the controller up grade,nothing has changed still the same,
Firmware version 4.3.6
Region Australia & Pacific
Power Cycles 381
Control Set FW version 1.4
Control Set HW version 4
Connected sensors
Connected sensors when manually memorized Front1, Front2, Rear1, Rear2
Connected sensor (actual) Front1, Front2, Rear1, Rear2
Settings
Audio Volume 5
Parking detection range 1
Silent Power-up Disabled
Dark Mode Normal
Parking enabled sensors Front1, Front2, Rear1, Rear2
GPS Antenna Enabled
PDC Speed Limit NONE
Working mode Parking and Laser Interference Defense
Pro mode Disabled
LID Speed Limit NONE
Radar Antenna Model STIR+
Radar Settings K, Ka
LID Time 6 seconds
Specific LID settings
Vitronic Poliscan
Speed scanner Enabled
Unicam Camera
Section speed control All sensors ON
NJL SCS
Speed-laser Enabled
Riegl
Speed-laser Enabled
Trafic Observer
Speed scanner Enabled
Stalker
Speed-laser Maximum Power
Alerts by Source Speed-laser
Marksman and UltraLyte 19
Atlanta SpeedLaser Stealth 0
Kustom ProLaser 1 0
Kustom ProLaser & ProLite 0
Redspeed SpeedGuard 0
Riegl 0
Stalker 0
LTI Truspeed 2
Unipar - SL700 0
NJL SCS 101 & 102 0
Jenoptik – Laveg 0
Leivtec XV 2&3 0
Laser Ally 0
Error Sensitive Lasers
Jenoptik LaserPatrol 0
Jenoptik TraffiPatrol XR 0
ProLaser 2 & Atlanta SpeedLaser 0
Speed Section Control
Camea - IR Camera 0
Speed Scanner
Traffic Observer 0
Vitronic Poliscan 2
Radar
K-band 248
Ka-band 8
X-band 0
POP 0
MultaRadar CD 0
with this controller f/w farked up if i go back to just laser and the plus, will the laser work on bt,
just one thing when i try to do fw on the controller it gives a kwik double chirp right at the end of up grade, some how seems as though its stopped short of doing the full upgrade like it gets cut off
Dinkydi, I am going to email you one of my Control Set files... Please let me know if it gets you closer to 3.0
Sent from my SCH-I605 using Tapatalk